6'x2'x3' | Custom HDPE-PVC Reptile Enclosure | Luxury Reptile Cage

This luxury reptile cage measures 6'x2'x3' and is expertly crafted with HDPE-PVC for superior strength and durability. Perfect for housing your reptile, this enclosure boasts top-quality materials and a sleek design.

What comes with your 6x2x3 enclosure

• Steady heat, humidity under your control. A solid top is standard, so the enclosure holds the conditions you set — humid for a tropical build, dry for an arid one, adjusted with the vents. Most setups run lower wattage than they would in a glass tank.
• A frame that stays looking new. 3/4" HDPE, USA made, UV stabilized and colored all the way through, in seven finishes. It will not delaminate, chip, rot or swell, with superior scratch resistance. It also resists fingerprints.
• Doors that glide. The glass rides on its own track, quiet and smooth, and the track continues down the sides of the opening for a finished edge. Both doors lift and tilt out for cleaning.
• Glass you can trust. Two 1/4" sliding tempered safety doors with every edge polished, certified to ANSI Z97.1 and CPSC 16 CFR 1201 Category II and etched to prove it — the more stringent of the two federal categories.
• Ventilation that moves with you. Six Adaptive Vents across the upper back panel. Every one takes a cover or a fan, so airflow changes as your setup changes through seasons and species. Covers and fans sold separately.
• Panels built for the climate inside. 1/2" American-made PVC on top, bottom, back and sides. Holds temperature steadily and stays true in heat and humidity.
• Wiring that stays tidy. Six cord slots in the top edge of the back panel for UVB, LED, heat and probe leads.
• Stacks without spacers. Two stainless steel dowels in our locking dowel system, which lines up across sizes so habitats, stands and hoods interconnect.
• A clean finish all round. Color-matched screw covers, so no screw heads show.

Built for bioactive

A living build keeps damp soil, roots and water against the walls every day. This enclosure is made for exactly that.

• Plastic, top to bottom. The PVC panels and HDPE frame are made for constant humidity. The frame will not delaminate, chip, rot or swell, and the panels absorb almost no water, so your enclosure stays square year after year.
• Tight seams. Every panel fits snug to the frame, so soil stays in and moisture stays where you put it. For a fully sealed build, run a bead of sealant along the inside edge of each seam.
• Easy to clean. Smooth surfaces wipe down with a damp cloth, and soil wipes off the frame with a dry paper towel.
• Room for real soil. A 6" lower frame comes standard, deep enough for a drainage layer and real substrate for burrowing, and it keeps the glass track above the grit. 8" and 10" frames are available in the options above.
• Airflow you can tune. Every Adaptive Vent takes a cover or a fan, and side vents can be added low or high, so fresh air keeps moving across damp soil without drying your build out.

Configure your 6x2x3

A deeper lower frame, perforated aluminum screen tops, lookout windows, side vents, climbing shelves, grommets, probe channels and custom cuts are all chosen at order time, in the options above. See every option explained.

Prefer fewer vents, extra probe holes or cord slots somewhere specific? Select it above, or email us and we will build it your way.

6x2x3 reptile enclosure specifications

Toad Ranch sizes are true-to-size exterior dimensions. A 6x2x3 measures exactly 72" x 24" x 36" on the outside, which is the number that matters when you are fitting it to a space.

Species suited to a 6x2x3

Ideal size for terrestrial species that spend their day on the ground — foraging, basking, exploring, and thermoregulating across a long horizontal gradient. Ample space for deep substrate to dig and burrow in, ground cover and rockwork, and enrichment across the floor.

These species do especially well in it:

• Bearded dragons
• Blue tongue skinks
• Uromastyx
• Ackie and other smaller monitors
• Ball pythons, corn snakes and kingsnakes
• Redtail and other boas

Growing into something bigger? Enclosures are expandable, so a 6x2x3 can become part of a larger build rather than something you replace.

Not sure whether this size suits your reptile? Email us.

Heating and lighting for a solid-top enclosure

A solid top helps maintain stable temperature and reliable humidity. Fit your own heating and lighting and the basking site goes exactly where you want it — and moves if your setup changes. Heating and lighting are sold separately.

A typical warm side

• Two heat fixtures side by side make one broad basking zone. Two lower-wattage bulbs work better than one hot point, and they can run at full output without pushing past your set point.
• Basking bulbs chosen for your species and your room temperature
• A deep heat projector for radiant warmth with no visible light, and as backup heat on the cool end

Lighting

• A 36"–48" UVB fixture, covering half to two thirds of the length. See Arcadia's lighting guide for the percentage your species needs
• An LED bar for daylight spectrum, and for plant growth in a bioactive build

Safety

Any heat fixture mounted inside needs a wire safety basket, particularly with snakes and climbers. Always pair heating with a thermostat and a probe. If you would rather keep heat and light outside the enclosure entirely, choose the perforated aluminum screen top above.

Assembly

One screwdriver, one screw size, no special tools. The front frame arrives pre-assembled with the glass track fitted; you fasten five panels to it. It goes back together at home the way it came apart here — same panels, same holes, same hardware.

Shipping

Free shipping on enclosures, stands and hoods anywhere in the continental US — the listed price includes it. Limited-access and remote destinations are quoted separately. This size ships freight on a pallet with lift gate service, which lowers it from the truck bed to ground level, delivered curbside. The carrier does not bring it inside or set it up, and it arrives flat packed for you to assemble on site.

Trusted by zoos, nature centers and professional breeders

Toad Ranch Cages builds to order in Webb City, Missouri. Veteran owned, USARK member, and a registered vendor with state and federal government offices. Every enclosure, stand and hood is hand assembled and checked in the shop before it is flat packed to ship.

Free shipping applies to enclosures, stands, and hoods within the contiguous United States. No matter what size.

For freight shipments, lift gate service is always included to ensure safe and easy delivery at your location. No hidden fees, no surprises—just reliable service from start to finish.

Unfortunately, Alaska and certain remote locations are excluded due to high carrier rates and limited-service availability. If you’re placing an order from an excluded area, please contact us first—we’ll provide a tailored shipping quote and help explore available options.

Shipping Cost on heating & lighting will be calculated at checkout.

Flat-Packed for Safe Delivery & Easy Assembly:

All enclosures, stands, and hoods are shipped flat-packed to prevent damage during transit.

Each unit is pre-assembled for quality assurance, making final assembly a simple process. Just five body panels and the pre-assembled front frame (with door track already installed) need to be secured—and there's only one screw size required.

Assembly is straightforward: a screwdriver is all you’ll need. Easy-to-follow instructions are included with every order and can also be accessed HERE.

Lead Time:

Our lead times are updated frequently—please check this page right before placing your order to ensure you have up-to-date production scheduling.

Lead time refers to the period between placing your order and the time it ships out from our facility here in Webb City, Mo.

We take pride in maintaining a reliable shipping schedule. Orders will ship no later than the timeframe listed below, and we keep a close eye on our workflow to ensure timeliness and transparency.

For Up-To-Date Shipping Times Click HERE.